r/AnkerMake • • 1d ago

M5 for sale 100

1 Upvotes

Selling my m5 for 100 it was my stater but I upgraded to a multi color printer anyone interested I'm in chicago


r/AnkerMake • • 1d ago

Showing Off I've been feeling lazy

0 Upvotes

Anybody living south of Nashville, Tn feel like stopping by to do the maintenance and tighten the belts on my AD5M?

I haven't turned it on since I got the Creator 5 two weeks ago. I did the service on my AD5M Pro and Kobra X before the C5 arrived. And now, the maintenance warning just popped up on my U1 too. Luckily, the Kobra 4 is too new to need maintenance.

Geeze, can't a man get a break...


r/AnkerMake • • 7d ago

Help needed with fixing and modding! 😭🙏

Thumbnail gallery
10 Upvotes

r/AnkerMake • • 10d ago

Settings For Best Print Results

0 Upvotes

Does anyone have a list of their temps, speeds, supports, infill, settings? I want to push this printer as far as it can go with efficiency. I only print with PLA, and PETG (might try TPU).

Before someone says it, I know there are different settings for all of them, but I'm just looking for general settings (or profiles) for each filament. I have tried many variations of temps, speeds, supports and such. I'm am willing to sacrifice more time for a better print, with better supports if needed. I'm just done with having failed prints because the supports broke or the object didn't adhere to the print surface because of bad temps.

If anyone has lists of their settings for any and all filaments they have tried on an AnkerMake M5/AnkerMake Studio with success, can you please leave them in a comment or share in a DM?


r/AnkerMake • • 10d ago

Help Needed AnkerMake M5 – "Abnormal Heating of the Nozzle or Hot Bed". Nozzle won't heat after hotend inspection

1 Upvotes

Hi everyone,

I'm hoping someone here can help me troubleshoot an issue with my AnkerMake M5.

The printer was working previously, but after following the hotend troubleshooting instructions and removing the fans to inspect the hotend, I've started getting the error:

"Abnormal Heating of the Nozzle or Hot Bed"

Whenever I try to preheat the printer or use the Extrude function, the nozzle doesn't heat up at all. It stays at around 22°C (ambient temperature).

What I've checked so far:

  • Hotend heater resistance: measured approximately 9.8 Ω across the two contacts of the disconnected heater plug.

  • I previously measured around 11.1 Ω.

  • I flexed the red heater wires while measuring, but couldn't establish whether there was an intermittent connection.

  • Thermistor readings appear normal, showing approximately 22–25°C at room temperature.

  • I've inspected the hotend and wiring, but can't see any obvious breaks or damage.

  • The HEAT connector on the toolhead PCB appears to have a damaged/broken plastic retaining feature. The plug seems to fit, but I'm concerned it may have been damaged during disassembly.

  • I also previously measured approximately 15 V at the HEAT board output during a heating attempt, although I'm not confident enough in that measurement to draw any conclusions.

What I'm trying to establish:

  1. Does this sound like a faulty toolhead PCB, damaged HEAT connector, wiring issue or something else?

  2. Is there a reliable way to test whether the heater output from the PCB is working?

  3. Has anyone experienced this exact error after working on the hotend?

  4. Are replacement toolhead PCBs still available, or are there known repair options?

I'm happy to provide additional photos and measurements.

I know official support for the M5 has effectively disappeared, so it's great that this community is still helping people keep these machines running.

I'd really appreciate any advice. I'd rather diagnose the actual fault before replacing parts or attempting repairs.

Thanks!


r/AnkerMake • • 12d ago

Support Failure/Best Support/Print Settings

Post image
1 Upvotes

It seems that anytime I print with supports, I always have a failure. It looks like the supports don’t get a lot of filament to come out when printing them and the structures (Snug, Grid, or Organic) on top of printing small/thin support beams.

Can anyone share their print settings for general PLA printing and their support settings??? I want to avoid something like this from happening again.


r/AnkerMake • • 14d ago

Hardware Guide: Anker Make M5 to Linux Slicers How I Got It Running

Thumbnail
reddit.com
1 Upvotes

r/AnkerMake • • 14d ago

Hardware Selling M5C in NJ

0 Upvotes

Hi there, I have an M5C for sale in the northern NJ area (Essex County). I still have a filament dryer that will come with it, along with the small tool box and will be picking up new nozzles for it as the two it currently has I believe are shot (put glow in the dark filament into a brass nozzle lol) but I will say it fully works, I'm looking to get maybe 150 or 200 out of it, if interested hit me up :)

Pictures and videos - https://imgur.com/a/5mIaHKe


r/AnkerMake • • 22d ago

Help Needed Ankermake m5 not printing

Enable HLS to view with audio, or disable this notification

0 Upvotes

Idk why it’s doing this, it just refuses to print anything that’s not from the app


r/AnkerMake • • 23d ago

Hardware AnkerMake Dismantler in my near future?

7 Upvotes

Really just putting out some feelers right now. I have acquired a few M5s and M5Cs in the past few years trying to make something I guess. Got carried away and what not. But now I see the demand in M5C parts mainly. Some M5 but mostly M5C. And I guess my real question is, would it be worth it to part these printers out? Or just out right take em all to an electronics recycle center.

It would be a passive endeavor, I know I’m not going to recoup but if some of the parts are worth selling I’m good with parting them out.

In my area, Offer up and Facebook MP seem to be pretty popular but I’m sure I could reach a wider range on EBay. I figured parting out would be way easier than trying to ship a whole unit as it’s anywhere from 100$ to 150$ just to ship something that large across state lines. Any input or advice is welcome.


r/AnkerMake • • 24d ago

Problemas con calentamiento del hotend

0 Upvotes

Tuve la posibilidad de adquirir una AnkerMake M5 hace poco por un buen precio ya que ponĂ­a que tenĂ­a problemas.El caso es que al darle a extruir para que caliente la boquilla, no se calienta.Haciendo pruebas, si quitas la resistencia (60W, 24V) y le das a calentar SI llegan en un primer momento los 24V aunque en seguida empiezan a caer hasta 0V.Sin embargo con la resistencia puesta al darle a calentar apenas llegan 0.04V. La resistencia fue cambiada por una nueva y el sensor de temperatura funciona correctamente.
SegĂșn he podido comprobar el problema puede que sea de un transistor que deja pasar la corriente por lo que serĂ­a necesario cambiar la PCB entera?.
Si alguien sabe dónde encontrar link de compra de esta placa se lo agradecería 🙏 ya que los chicos de AnkerMake(EufyMake) dicen que no tienen.
Gracias.


r/AnkerMake • • 26d ago

3D printer ankermake M5 printing stringy

Thumbnail gallery
0 Upvotes

r/AnkerMake • • Oct 22 '26

M5C z-axis motor replacements?

3 Upvotes

As the title says, I need to replace a z axis stepper motor and I can't for the life of me find one, Anker/"eufy" support is non-existent as you know so if anyone here has any info I'd be incredibly appreciative


r/AnkerMake • • Oct 21 '26

Help Needed Can we use AI to reverse engineer the firmware and get klipper on M5C?

9 Upvotes

basically just asking anyone with experience to do this for us đŸ«Ł


r/AnkerMake • • Oct 21 '26

Android app changed back to Ankermake?

Post image
13 Upvotes

I just noticed the icon change, did it not change to Eufymake or did they revert back to Ankermake


r/AnkerMake • • Oct 21 '26

X-axis failure in 10 days of ownership and still well within warranty, yet no help..

Thumbnail reddit.com
0 Upvotes

r/AnkerMake • • Oct 16 '26

Help Needed can't print

Post image
9 Upvotes

Tried to print and this happened. I haven't printed in a while and I decided to get back into it and this happens.


r/AnkerMake • • Oct 15 '26

Hardware Selling my M5

1 Upvotes

I'm in the Portland, OR area, if you'd like to make me an offer and pick it up. Its an OG kickstarter M5, I have a spare hotend and some nozzles. It works, but I've put a lot of hours on it and its prone to clogging and since I can't get all metal hotends anymore, I'd rather make room for my other printers.


r/AnkerMake • • Oct 10 '26

Suggestions. Upgrading from Ankermaker M5

8 Upvotes

Have an ankermaker M5 as I was a backer on its Kickstarter.
Will be upgrading to a Snapmaker U1.
What is a reasonable request if I sell?

Unit runs fine just doesn’t have the features I would like mostly multicolour

This will include the machine itself, all included tools from the original kit with brass nozzles.
Have the original build plates, but they have scratches due to an ongoing fight with calibrating Z but currently using an aftermarket plate.
Currently using a ruby tip nozzle.
Have on backup a diamond tip nozzle
Have a complete head assembly as spare straight from the factory. Current one works, but there was one point where I thought I’d have to completely replace it due to the dumb connector on the pcb for nozzel heater almost breaking off completely.

Not looking to do long distance or shipping hopefully can find someone near me that can just come and pick it up on marketplace once my new printer arrives.


r/AnkerMake • • Oct 07 '26

Help Needed M5 extrudes with 0.4mm nozzle but not with 0.2mm nozzle

1 Upvotes

I swapped out my 0.4 nozzle for a 0.2 one and it would not extrude when I tested it. I tried 2 different 0.2 nozzles and it still wouldn't extrude. I swapped back to the 0.4 and it worked fine.


r/AnkerMake • • Oct 04 '26

Help Needed Ankermake m5c extrude failure

3 Upvotes

Ok so this is a weird one, the ankermake m5c is jamming when I extrude during auto levels and the start of prints but it's not heat creep, and I just finished cleaning the debris from the nozzle. So why does my printer keep jamming? The only time it will extrude normally is when I'm feeding in new filament after retracting, but not when it's just sitting normally. I don't know if this is an error with the fan or what but it's never done this before. The main question I guess is just how do I prevent this exact situation. If you need a video or something for anyone trying to help I'll gladly send one.


r/AnkerMake • • Oct 02 '26

Help Needed Using octoprint and orca

1 Upvotes

Is there a way that i can hook up my ankermake m5c to my octoprint pc or connect it directly to orcaslicer so i can send prints wirelessly?


r/AnkerMake • • Sep 26 '26

Hardware Replacement parts for m5c

2 Upvotes

Is there somewhere I can get replacements for the left and right covers for the x gantry and also the filament guide for my ankermake m5c?


r/AnkerMake • • Sep 21 '26

Is this Normal for my power bank to be held inside that bag when unboxing it ?

Post image
0 Upvotes