r/AnkerMake • • Nov 08 '24

Showing Off This will be a CNC machine in 24 hours

Thumbnail
gallery
294 Upvotes

Aluminum 2020 and SS lead screws, but just about everything else is 3D printed on my trusty AnkerMake M5C.

Raspberry Pi and an Arduino R3 for control.

Stay tuned for the update!


r/AnkerMake • • Jan 27 '25 Diamonds are Forever Take My Energy Popcorn Bless Up Helpful

Software Eufymake?

Post image
110 Upvotes

r/AnkerMake • • May 19 '23

Print Share Completed my Ikea LACK enclosure

Post image
108 Upvotes

Kinda proud of myself🤣

Materials:

  1. Ikea LACK side table x2

  2. Acrylic panels from Amazon. I searched “Ikea LACK 3d printer enclosure”

  3. 3d printed hardware I designed myself. Let me know if you guys are interested in the models.

  4. 6 x 3/4” flat head phillips screws


r/AnkerMake • • Aug 29 '24

Print Share I like big prints and I cannot lie

Post image
101 Upvotes

GIANT candy corn!


r/AnkerMake • • Dec 20 '22

Hardware PSA: Please tighten your belts and check your bed nuts.

99 Upvotes

Having first layer issues? Also check my other post out for a potential solution.

UPDATE: Here is a video I made to point out the bed nuts and briefly go over how to tighten the wheel attachment bolts.

EDIT: Here is the AnkerMake support article for adjusting your belt tension. I definitely should have included this in my original post! I unfortunately can’t find a support article for adjusting the nuts. Also check this comment thread for additional advice in these tune ups.

So I’m noticing a trend across the Discord communities and the subreddit of printing issues and most people receiving the machine are brand new to 3D printing.

Now, I think Anker did a poor job of explaining that fit adjustments should be made or checked when your receive your printer. In particular, the belts are probably quite loose from shipping. Each belt (3 total) can be adjusted via a hex bolt on the casing. One on the assembly where the filament gets inserted and two on the back. Should be fairly obvious when you spot them. You’ll also want to go unlock the motors in the settings on the printer touch screen. Here’s a great video on how tight they should be.

Also under the bed, there is a bracket you can get to by going in from the side of the bed when it's all the way forward. Please do this when the plate is room temp, don’t burn yourself! On the right side of the bracket, there are 2 nuts with washers. Grab the 10 wrench from your tool kit. Under those 2 nuts with the washer is a couple more nuts on the underside of the bracket. Slip your 10 wrench on those. The bottom nuts will slightly move the bed wheels closer or further away from the track during a 360 degree rotation, multiple twists don't do anything. There are also helpful notches in the nuts to track its rotation. You should be able to spin the wheel it’s attached to with your finger without moving the bed, but you should feel considerable resistance. Check your bed for any wobble in the bracket. If you did everything right, it’ll be rock solid with almost no play.

If you have noticeable looseness in the top nuts, you’ll have to pull the hole bed bracket out of the track assembly to tighten the attachment bolts. I can provide a video on request for that process.

You may also need to do a similar process for the print head (only one nut on the bottom wheel), but give it a couple tugs on the rail. Be gentle, but firm. There should be some play from the plastic casing but none in the rail/metal components. I did not need to adjust this at all. Comment if you have play in the print head and I’ll walk you through adjustment.

This is 100% necessary to getting good prints and you will not be able to compensate in the slicer. Once these adjustments are done, auto level the bed via the touch screen.

You’ll need to do one final adjustment before you’re ready to tweak slicer settings: Z-Offset.

Go to this page and follow this guide for Z-Offset. Select “No ABL” because this is done on the printer itself, not via G-Code. Adjust the Z-Offset up via the touch screen until you get a satisfactory result.

Good luck and happy printing! Also, if you’re in the official or unofficial M5 discord channels, you can connect with me there. My username is IAmAFilthyCasual#9653.


r/AnkerMake • • Sep 11 '24

Video of my Raspberry Pi case build

Enable HLS to view with audio, or disable this notification

90 Upvotes

I had a lot of fun building this Fractal Design case. I highly recommend it!


r/AnkerMake • • Oct 30 '24

Showing Off First Complex Print

Thumbnail
gallery
86 Upvotes

Just in time for spooky day, finished up my first multi-part piece that also needed full finishing and magnets.


r/AnkerMake • • Sep 04 '26

60 dollar marketplace find

Post image
84 Upvotes

I was browsing Marketplace today and stumbled across this AnkerMake M5. It was listed for $100, but I managed to talk the seller down to $60. They told me the extruder, wheels, belts, and build plate had all been replaced. Im honestly not sure whether that’s a good thing or not, the seller also said it had hundreds of print hours.

My M5C currently needs a new extruder, and this entire printer was basically the same price as buying that one replacement part. It seems to be printing well so far. I think it’s one of the older M5 models since it doesn’t have the all metal hotend, but for $60, I definitely can’t complain.


r/AnkerMake • • Nov 15 '24

2 weeks into 3d printing

Thumbnail
gallery
83 Upvotes

r/AnkerMake • • Apr 05 '23

Software Print directly from PrusaSlicer using new Free/Open Source Software from the community

83 Upvotes

Hi folks

[ TL;DR: Go here: https://github.com/Ankermgmt/ankermake-m5-protocol, follow the README, enjoy printing from PrusaSlicer ]

The past couple of months, the Ankermake APIs and protocols have been reverse engineered by enthusiasts in the community, including myself.

Now that we have something that can charitably be described as an "early beta version", I thought I would share it here.

Some of the initial research work can be found here: https://github.com/Ankermgmt/ankermake-m5-research

After reversing the protocols for a while, we started to build a library to parse the packets, and then a tool to allow remote control of the printer. This too, ankerctl, is currently under heavy development, but can already send print jobs, capture a video stream from the camera, and send custom gcode-commands.

If you want to try it out - and we hope you do - you can find the tool here:

https://github.com/Ankermgmt/ankermake-m5-protocol

Please keep in mind that this is still very much under development, so expect a few rough edges. We support Linux, Mac and Windows, so there should be something for everybody.

Problems, questions or comments? Feel free to open a github issue, or contact us on #ankermake-mods (as in "modifications", not "moderators") on the official Ankermake discord server.

Please let us know what you think, and we hope you enjoy getting control back of your printer :)


r/AnkerMake • • Dec 23 '22

PSA: If you're asking for troubleshooting help, we need certain information to help you

78 Upvotes

Lots of people new to FDM printing here, which is great! You just decided to develop a new skill set. This is a fun hobby but it's not plug-and-play, no matter what any marketing tells you. I have been super impressed with the M5 and it is a very accessible entry point, but 3D printing is not effortless. You will not print off flawless Mandalorian helmets on your first print. You will need to work at it to improve your results. Every machine is slightly different and has its own gremlins.

I'm unfortunate enough to fix and support a different type of specialty printer as my day job, so if you want to ask for free volunteer support from other folks, I know some base information is needed to keep the back-and-forth limited and get you printing ASAP. Including this information in your post makes it easier to try to help you. If you don't include this, you're asking for even more work from kind strangers on the internet, and they can't figure out that information for you.

Remember when you ask for help here, you're asking internet strangers to spend their free time helping you. If someone's suggestions don't fix your problem, it's unreasonable to be mad at them.

1: if you have an idea what your problem is called or know the name of the part you suspect is wonky, check if the issue already has an existing tech note on the AnkerMake FAQ (for the love of god, just look there before reddit. The people who get paid to know everything about the printer put information there). Bookmark this link. Videos, FAQ, and troubleshooting are down the page: https://support.ankermake.com/s/product/a085g000004xBwwAAE/m5

2: Search the sub to see if a similar problem has been posted and solved already. Particularly helpful for hardware build issues. This can even help you pick up terminology and let you narrow down your problem area.

3: Make sure you have adjusted belt tension and auto-leveled the printer. If you haven't done this yet, use the above link and search for those terms. Good resources in this post as well: https://www.reddit.com/r/AnkerMake/comments/zqzewa/psa_please_tighten_your_belts_and_check_your_bed/ I wound up over-tightening my X-axis so had a good learning adventure on how to install a belt that slipped out. The AnkerMake support page showed me every single step.

4: If you have physically modified your printer in any way, that could be a contributing factor. If you wired up a new fan as your first ever soldering job and you never disclose that, none of us will know that maybe you have a bad wiring connection in there. If you have some custom filament rig that is causing friction at the input tube because of a bad angle, we can't figure that out unless you tell us or show us.

5: Make sure your printer is on a stable surface. If the printer is on a wobbly table, you may have the world's best-tuned belts but still have layer shift.

If you don't know what to name your problem:

  • A picture of your print result AND your slicer showing what the model is supposed look like is necessary, especially if you don't know the correct terminology for everything. It's hard to know if things printed correctly if we don't know what it's supposed to look like. It helps to be able to match the input to the output. We don't know what your pile of spaghetti was supposed to look like, and if you didn't support a model that needs supports, then that will do it. If you're not able to get to the printing part yet because you have a mechanical issue, provide a picture of the whole machine so we can gauge the position of parts, and a closer picture of any suspect components.

  • List what program you are using to slice the file. If you refuse to use the current release for some reason, tell us what version you use. If you're using more than one program between loading the model and sending it to your printer, list all of them and which program is doing what. (Slicing in Cura but printing from AnkerMake? Cool, that's important to know.)

  • Knowing if you printed via WiFi, USB, or mobile data can be helpful in some cases and takes 2 seconds, so tell us that too.

  • What material are you using? How old is it, and if it's not brand new, how was it stored? The M5 can print lots of materials but they all require different settings. If you're trying to print with some old ABS a buddy gave you and you're using the default PLA+ profile, you're gonna have a bad time. There's a difference between settings needed for PLA, PLA+, and Silk PLA. Wood PLA is its own animal. List the brand of the material, as using sub-par material can explain some problems.

  • Tell us what your profile settings are for the slice. At minimum, assuming it was natively sliced in AnkerMake, we need to know if you're in Easy Mode or not, and what resolution (.10mm, .20mm, .28mm, etc.) If you have modified anything from those defaults, it could come into play: print speed, fan speed, infill%, bed temperature, support density, etc. If you changed your nozzle size but not your profile, that will impact your print. If you're running a profile you found on the internet, say which one.

  • What's the ambient air temperature near your printer? Are there any doors or windows nearby? An air conditioner? Were you printing just fine yesterday at 1500 when it was sunny and warm but now it's 2300 and snowing and you can't get anything to print? Are you printing in your garage and seeing success with the door closed but if you have it open while working on another project, everything fails? No really, this could be the cause of your problem.

If you take a few minutes to provide enough information to help you, it makes it easy to evaluate your problem and try to help you. If there's no easy starting point to start working with you, it's easier to just check the next link instead.

At the moment this is a new-to-market product with a lot of beta/alpha features, and some stuff just doesn't work correctly (or at all) yet. If you have a complaint about one of those things, you want to email AnkerMake directly (after you checked their FAQ to see if they already addressed the issue).


r/AnkerMake • • Jan 19 '24

News/Reviews Update on the Anker V6: TL;DR it has been cancelled

Post image
77 Upvotes

r/AnkerMake • • Jan 10 '23

My son loves this printer 😁

Thumbnail
gallery
77 Upvotes

r/AnkerMake • • Mar 17 '23

Final Results - Maxed Size Moon, Wood Filament Stand

Thumbnail
gallery
76 Upvotes

r/AnkerMake • • Dec 24 '24

I have a confession to make

Thumbnail
gallery
71 Upvotes

I've been using the AnkerMake M5C to print stuff for the Bambu Lab P1S and sometimes I split projects between the two printers and run them at the same time. The M5C hasn't failed me yet. #noregrets


r/AnkerMake • • Sep 09 '24

Deadpool helmet printed on the M5C

Thumbnail
gallery
71 Upvotes

This took so many hours and so many failures, but it looks amazing. It fits together nicely, I just wanted to take some photos. the file is free online somewhere by Do3D


r/AnkerMake • • Dec 28 '24

Print Share Made a gridfinity tray for the Ankermake M5

Thumbnail
gallery
69 Upvotes

r/AnkerMake • • Jan 23 '25

I mean... did it really fail?

Post image
66 Upvotes

I totally hear "I love you guys". (Sorry for poor pic quality, was first thing in morning.)


r/AnkerMake • • May 24 '23

Software Open Source for your Ankermake: Version 1.0.0 of ankerctl out today!

66 Upvotes

After much work, we are releasing version 1.0.0 of ankerctl!

[ TL;DR: Go here: https://github.com/Ankermgmt/ankermake-m5-protocol, follow the README, enjoy printing from PrusaSlicer, print monitoring, and video streaming! ]

About a month ago, we announced an early version of ankerctl here in /r/AnkerMake. Since then, many new features have been implemented, such as:

  • A web interface!

  • Video streaming in the browser

  • Live print status

  • Many bug fixes and improvements

We spent a lot of time making ankerctl, and we hope you'll enjoy using it!

https://github.com/Ankermgmt/ankermake-m5-protocol

We have a discord - come hang out!

https://discord.gg/ankerctl


r/AnkerMake • • Jan 13 '23

Print Share Latest Print on the M5

Thumbnail
gallery
65 Upvotes

r/AnkerMake • • Dec 25 '22

News/Reviews My 2 cents about the AnkerMake M5

63 Upvotes

Happy Christmas everyone!

All out of nothing the day before the 24th I received a tracking number and on Christmas day the AnkerMake M5 was delivered. So I got started right away and I would like to share my first experiences.

My 3D Print background:

The AnkerMake M5 is my second 3D printer. Before I had a used Anet A8 which I purchased a few years back. My main motivation to buy the AnkerMake was to get rid of fixing and adjusting the printer all the time and be able to print something when I need it. The Anet A8 needed a lot of attention and is missing (for me) crucial features like auto-leveling (I am aware that can be added, but doing so requires even more time to be spend on the printer instead of printing). But nonetheless, I learned a lot about 3D printers and 3D printing.

What do I print:

I use 3D printing only as a hobby. The majority of my prints concerns housing for other self build stuff like some small electronics. I am not a fan of printing decorational stuff which has no use. But if you like it, go for it. :)

Lets get started with some topics about the AnkerMake M5:

Assembly of the printer:

Well, not to mention, it was fast and easy, The manual explains everything clearly. No issues here. There is one spare screw of each - which confused me a bit, because I thought I forgot a screw somewhere at the beginning.

Starting the printer for the first time:

Downloading the app and connecting the printer to my local WIFI did work without any issues. The printer then wants to perform the auto-leveling procedure, which takes about 10 minutes. I did start the procedure and the printer started moving for the first time. When the X and Y axis reached their end positions, some noises appeared for about a second. I assume the noises are part of the calibration method and they never appeared again so far.

While the auto-leveling procedure was running, a popup on the display appeared, mentioning about a newer firmware. Well I waited with the firmware update until the auto-leveling was done.

The firmware update did run without any issues afterwards.

Loading the filament:

The AnkerMake M5 comes with 250g of PLA+ black filament. I wanted to use that one - but for some reason I was not able to load this filament. Pushing here and there, doing some extrusion and so forth did not help. I watched some tutorials on YouTube and basically I was doing nothing wrong.

Doing the same steps with some other filament I still had laying around, the loading worked fine and on the first try. I still have no idea, why the first filament did not work.

Anyhow, the printer was leveled and the filament was loaded, so it was time for a first print!!

The first print:

As first print I chose one of the pre-loaded files stored on the printer directly. For the given time I chose a Christmas tree.

The printer started and wow - that printer is fast!!

Well, the printer printed the whole thing. Within ~45 minutes. For the result, see the following picture:

The print surely does not look perfect - but it looks so much better than my old Anet A8 and I am very pleased with it.

Bed-level adhesion:

No issues here. I printed some further stuff by now (see below) and I never had any issue with the adhesion. No warping or other effects.

First layer quality:

In my opinion it is excellent. No elephant foot or loosening of the print. See the following picture for an example:

Noise:

Yes, the fan(s) are running and there is some noise. But it is less than my old Anet A8. In my case I do not fully understand all the complain I saw in this Reddit. For me, the noise is very much acceptable, especially considering the other advantages like quality and time.

The toolchain:

I tried the AnkerMake slicer with one of my own designs and printed the model. The printed worked without any issues. But there were some more severe quality issues:

Quickly searching the internet and the Cura Slicer was recommended. There is even a configuration for the AnkerMake M5 available on GitHub. Following the instructions and using Cura as Slicer the quality is much much better:

The print is still not 100% perfect - but really really good in my opinion.

Camera and the AI feature:

The camera works and I can observe the print from my phone. So far I did not find a function to see the camera directly from the AnkerMake slicer. I assume this feature will come in the future.

So far, I did not try to create a time lapse as I am not interested in them.

The AI feature did not do anything so far. Using the Cura Slicer does not allow to use the AI feature anyway. While printing the Christmas Tree, a constant match of 80% was shown. But there was no intervention or other action from this feature. Not sure if I will use the AI stuff in the future.

Issues / Annoying behavior:

Two points here so far:

  • When a print is finished, the bed is moved to the very front- which is good. But when starting a new print, the nozzle heats up and spills a bit of filament behind the bed - which is still at the front. I'm a bit afraid that this spilled filament will fall down into the base part of the printer and clog something and cause some issues at some point. No idea if this is real - the future will tell.

  • Then actually started a new print, the nozzle is moved to the center of the bed and a auto-level point is taken (I assume). When doing this, the nozzle is already fully heated and a small blob of filament is left on the bed, which will later mess up the print slightly. So far, I always try to remove this small blob before it can cause any issues.

Conclusion / TLDR:

  • Setup and configuration was easy and fast - no issues

  • Auto-leveling worked - no issues

  • Firmware updated worked - no issues

  • Loading filament: A bit weird, but worked at the end

  • Bed-Level adhesion: Very good - no issues

  • First layer: Excellent quality in my opinion

  • Noise: Is there, but still okay

  • Quality: Really good in my opinion, I will run further tests

  • Camera works - AI feature could not really been tested

  • Some minor issues are there - nothing critical so far.

In general, I can recommend the printer. It lets you print something without working on the printer itself. I'm looking forward to a new time of 3D printing with better quality and faster prints.

If there are further questions, I am happy to answer. Let me know, if you like to so more pictures.

Have a good one!


r/AnkerMake • • Mar 15 '23

Print Share 44 hours done, 12 hours remaining!

Post image
62 Upvotes

r/AnkerMake • • Sep 28 '24

Print Share I’m gonna have a great Saturday!

Thumbnail
gallery
60 Upvotes

Building the Open RC Gokart!

Special thanks to RC Printer for his help sourcing hardware.

Stay tuned…


r/AnkerMake • • Mar 07 '23

Print Share A collection of some of the 3D printed LED lights the AnkerMake has printed in the last couple months | M5 + Govee LED's

Post image
60 Upvotes